10% OFF this Easter Weekend - Use code EGG10 (min spend £50) 

FAST UK DELIVERY
Secure Shopping
Fully Stocked UK Warehouse
Hassle Free Returns
Trusted by The Trade
Friendly Knowledgable Team
20 Years Established
Click & Collect
CLOSE
HAVE A QUESTION?
CLOSE
SHARE WITH A FRIEND

Enter your name, and your friends name and email address

CLOSE
PERSONALISE YOUR ITEM
CLOSE
BULK ORDER QUOTE
CLOSE
Stock Notification

Vacuum Switch Dryseal

Single Pole 2 Terminals

Extended 1 Year Warranty

In addition to the manufacturers standard warranty (usually 1 year) we also offer the opportunity for you to extend this warranty by a further 1 year for a one off fee. This can be arranged at the point of purchase or within a limited time afterwards.
An extended warranty is an easy way to protect your purchase, against any manufacturing defects causing breakdown. You will benefit from free repairs for the term of the warranty period & If your equipment can't be repaired then we will replace it free of charge.(A delivery surcharge may apply for non UK mainland addresses)
This warranty and the standard manufacturer’s warranty does not cover general wear and tear, abuse or misuse or incorrect installation.
If you would like any further information on our extended warranty scheme please call our Hydrospares team on 01326 371 488 OR email us at info@hydrospares.co.uk

LID: 881
Available While Stock Lasts
single pole
2 spade connections
height: 48mm
3667
3 In StockSame day dispatch if ordered by 14:00
Fast UK Delivery
Vacuum Switch Dryseal
£56.99

Last Few Available

Vacuum Switch Tecmark - VTBS3002-950 To be used on the suction side of the pump to indicate sufficient water flow through the heater

Height: 48mm
Width: 25mm at widest point
Depth: 48mm from front to rear spade

Up to 125vac. 21A (5kW) 3/8 inch MPT screw thread. Common used with in line bath heaters assembled before the water enters the pump wet end.

 Commonly used as an interlock device to sense gas, air or water pressure at a specific point. Usually Fitted to the suction side of your pump.

 Tecmark Series V4000 Vacuum Switches convert a negative pressure signal to an electrical output. In response to a change in negative pressure, movement of an elastomeric diaphragm opens or closes an electrical circuit based on a predetermined pressure set point. The Series V4000 features cost effective, snap-acting electrical switches and field adjustable set points. Vacuum ranges from -2.5" (-600 Pa) Water Column (W.C.) to -10.75 PSI (-75 kPa) are available. Consult factory for vacuum levels outside listed ranges. Series V4000 switches assure control stability through wide and variable temperature and humidity conditions and assure uninterrupted service under extreme shock and vibration. As with all Tecmark® products, series V4000 switches provide superior performance and 100,000 cycle life under full mechanical, electrical and thermal loads.

Provide on/off control of:

  • Electric or gas heaters
  • Pumps
  • Small air compressors
  • Electric strip heaters in VAV systems
  • Waste oil heating systems
  • Residential boilers
  • Other electrical equipment in pneumatic or fluid flow systems

Basic Construction

  • Elastomeric diaphragm eliminates the need for an oil barrier
  • Field adjustable pressure set points. Factory calibration available upon request
  • Built in over pressure protection designed to eliminate stress on other critical operating components
  • UL Recognized, Canadian and United States, as an operating, limit or safety control
  • Available with CE approved electrical snap switches

Available Features

  • Vacuum ranges from -2.5" WC to -10.75 PSI (-600 Pa to -75 kPa)
  • SPST or SPDT switching logic
  • 1/4" male quick connect for electrical connections
  • A variety of mounting pan and pressure fitting materials; stainless steel, injection molded plastic and plated steel
  • Wide array of pressure fittings; 1/8" NPT male, 1/4" NPT male, 3/16" barbed, 1/8", 3/16" or ¼" compression, or 1/8" NPT female with ½" conduit male external thread for mounting
  • Optional vacuum set point locking mechanism
  • Specialty diaphragm materials; Buna-N, EPDM, Hydrin

Ratings and Specifications

  • Maximum Operating Pressure and Hydrostatic burst pressure, varies based on model configurations. Consult factory for specific application needs.
  • Electrical ratings to 25 amp, 250 VAC.
  • Field tested critical components specifically selected to operate reliably in temperature extremes of 32° to 190° F (0°C to 88°C).
  • 100,000+ cycle life under full mechanical, electrical and thermal loads.
Downloads & Articles
Customer Reviews

Write a review

star
star
star
star
star
Questions & Answers

Is this switch adjustable. What is the vacuum at which it can be set to switch. Is it normally open or normally closed

REVIEWED BY: Norman Wheat

Please refer to data download sheet on this listing.

Answer from: Andrea

Submit a question

 
warning
Confirm add to basket
Return to listing
Add to basket
COMPARISON BASKET
COMPARE